- #Nvidia web driver 10.13.2 17c88 how to
- #Nvidia web driver 10.13.2 17c88 install
- #Nvidia web driver 10.13.2 17c88 drivers
- #Nvidia web driver 10.13.2 17c88 windows 10
- #Nvidia web driver 10.13.2 17c88 password
Here are my specs to start off: Intel i7-4790k, z97x-gaming 7 MB, 32 Gb memory, NVIDIA GeForce GTX 660 Ti 2GB I don't have another NVMe SSD to test out.
#Nvidia web driver 10.13.2 17c88 windows 10
The NVMe was running Windows 10 previously with no issues, so I don't think it's a hardware issue. Apparently High Sierra has native NVMe support, but it's not liking me so far. I've tried with vanilla IONVMeFamily from original install, IONVMeFamily and hackrnvmefamily both in SLE, just hackrnvmefamily in SLE (removed IONVMeFamily, but no NVMe shows up). Kernel file: /BuildRoot/Library/Caches//Sources/IONVMeFamily/IONVMeFamily-356.1.4/IONVMeBlockStorageDevice.cpp Kernel AppleNVMe Assert failed: ( fFatalState = false ) ErrorUnlock file: /BuildRoot/Library/Caches//Sources/IONVMeFamily/IONVMeFamily-356.1.4/IONVMeController.cpp AppleNVMe Assert failed: 0 = (status) line: 4608 Kernel AppleNVMe Assert failed: 0 = (status) >I've got it booted and running on the HDD, but when I try to copy over to the NVMe via CCC, it gets about 20gb in and then the following shows up in log files and IO stops on the NVMe.
#Nvidia web driver 10.13.2 17c88 install
I've tried both Unibeast and a vanilla install with clover and required kexts to install to NVMe It gets about half way and then says something about the bless tool not able to bless the filesystem. I can install High Sierra to the HDD with no issue, but not to the NVMe. I've got a Lenovo M710 Tiny i7-7700 with a 512GB Samsung NVMe drive (PM981 rebranded for Lenovo) and a 500GB WD5000LPLX HDD. Just didn't notice until after trying to drop it in the second tim (I actually already had the Lilu.kext in place before updating, just to make that clear. In total, I am using AppleALC.kext for my audio, FakeSMC.kext, Lilu.kext, and NvidiaGraphicsFixup.kext. Took me a few times, but I eventually got it! And then my system was good to go. So in that minute, I was able to mount my drive and copy the kexts over. The only problem was that after about a minute or so, the system would reboot because I didn't have the proper kexts in place. I eventually figured out that after downloading the appropriate Nvidia web drivers, I was able to boot into high sierra normally.
#Nvidia web driver 10.13.2 17c88 how to
This part also took forever because I could not figure out how to get these texts into CLOVER>kexts>other since you can't mount your drive in safe mode. My intel graphics are disabled in my BIOS.Īfter getting in, I downloaded NvidiaGraphicsFixUp.kext and Lilu.kext.
#Nvidia web driver 10.13.2 17c88 password
This was just dumb luck, but after hours of trying to get past that black screen just to get to the GUI, I randomly decided to type in my password and press enter and miraculously, my display glitched on! another thing to mention is that I was running a single DVI display from my gpu. I was able to get run -x and get into safe mode, but I was stuck on the black screen. I was able to get into recovery mode, but I'm useless with terminal, so I did not make a lot of progress in that route. I'm not sure if uninstalling helped or hindered my process, but it was worth mentioning.Īfter the update, I was stuck in a boot loop. This was unrelated to me preparing, but it seemed to reduce my former glitch problem.
#Nvidia web driver 10.13.2 17c88 drivers
Yesterday, I did another direct update to 10.13.2 that resolved everything and I figured I would share my experienced.įirst off, I uninstalled my web drivers prior to updating. Recently I did a direct update to 10.13.1 and experienced a ton of glitchy graphics issue, which seemed to be the case with a lot of 6 series graphics cards on here. Customize: NVIDIA Web Drivers Boot Flag & Nvidia Graphics Fixup Bootloaders: Clover UEFI Boot Mode + Emulated NVRAM USB: 3rd Party USB 3.0 & Increase Max Port Limit 200 Series Network: Realtek->RealtekRTL8111 v2.2.1 Audio: Realtek ALCxxx->ALC887/888b (PERHAPS I NEED TO USE "200 / 300 Series / X299 Audio Device ID Patch?) PWR: Rosewill Glacier Series Continuous 80 Plus Bronze. MEM: Ballistix Sport LT 16gb (8GB x 2) DDR4 2400 MT/s
The geekbench results both literally and via inference describe the chip as an intel i5-8600k, so I am less concerned about this. In the "about this mac" display the Processor is listed as 3.6Ghz "3.6 GHz Unknown". Shutting-down the computer results in a restart every-time.ģ. when I plug my headphones into either the front or rear 3.5mm port) is not working nor is the computer appearing to recognize the output device.Ģ. This is my first time making a hackintosh and it has gone pretty well overall with a few bugs I'm hoping you call can help me debug.ġ. /lgbt/ - Lesbian, Gay, Bisexual, & Transgender.